Skip to content

Touch screen test

Find dead zones and count touch points.

Covered 0%

Squares left –

Drag a finger over every square.

Drag over every square. Any that stay empty did not register.

Runs on this device. Nothing is recorded or sent. Browser reports – touch points.

Edge and corner check

Cover the grid to see which part of the screen responds least.

Works with fingers, a stylus or a mouse. On iPhone, the test fills the page; Safari does not allow full screen there.

How do you test a touch screen?

A touch screen test shows where the screen registers your finger: slide one finger slowly across the whole area in Dead zones mode, row by row, like mowing a lawn. Every square your touch passes over fills in. When you have covered the area, any square still empty is a place the screen did not report a touch. Go over it again a few times: a square that stays empty after several slow passes is a real dead zone, not a missed spot.

Press Full screen before you start on a phone or tablet. Edges and corners are where faults usually hide, and the page's own margins would otherwise keep you away from them. Squares are about the size of a fingertip, so the grid shows where a fault is without asking you to hit single pixels.

  1. Clean the glass and dry your hands. Water and grease cause false touches.
  2. Unplug the charger. A poor charger is a common cause of jumpy touch.
  3. Cover the grid, then switch to Multitouch and put down one finger at a time.
  4. Draw slow straight lines along the edges in Draw mode, and look for breaks or wobble.

What each mode checks

The three test modes
ModeWhat it findsA pass looks like
Dead zones Strips or patches that ignore touch, often along an edge or a crack Every square filled after one or two passes
Multitouch How many fingers the screen tracks at once; fingers that vanish or merge Each finger gets its own numbered ring, up to the device limit
Draw Jitter, breaks in a line, ghost marks you did not make Smooth, unbroken lines that follow your finger

Source: The Daily Summit touch screen test.

The number under the test area comes from your browser. MDN describes navigator.maxTouchPoints as the most simultaneous touch contacts the device supports. Desktop computers without a touch screen report 0, and phones typically report 5. The multitouch counter shows what actually happens when you put fingers down, which is the more useful figure: a screen that claims 10 points but drops the fourth finger has a problem. If the glass itself looks faulty, with specks or stuck colors, run our dead pixel test as well.

How does a touch screen sense a finger?

By measuring a tiny electrical charge. Almost every phone, tablet and touch laptop uses a capacitive screen. A fine grid of transparent electrodes sits under the glass, and a controller chip measures the tiny electrical charge at each crossing many times a second. A finger is conductive, so it changes the charge where it rests, and the controller works out the position from the pattern. That is also why gloves and long nails do nothing, and why a drop of water can look like a finger.

The design explains the faults you see. A crack can cut the electrode lines, leaving a dead strip that runs all the way across. Electrical noise, often from a cheap charger, can make the controller see touches that are not there. And a thick or badly fitted screen protector puts more distance between finger and electrodes, which weakens the signal near the edges first.

What causes touch screen problems, and how do you fix them?

Cracks, dirt, moisture, screen protectors, chargers and software are the usual causes, and the table lists what each looks like. The problem may also be the pointer rather than the screen: on a laptop, our mouse test checks buttons and scrolling, and a Bluetooth controller can be checked with our gamepad tester.

Touch screen problems: likely causes and what to try
SymptomLikely causeWhat to try
A strip or corner never fills Damaged digitizer or connector Restart; if it persists, repair
Touch works on and off Dirt, moisture, protector, charger Clean, remove case and protector, unplug
Ghost touches Interference, water, faulty charger Unplug accessories; move away from other electronics
Works in safe mode only An installed app (Android) Remove recent apps one at a time
Whole screen dead Driver, software or hardware failure Restart; on Windows, reinstall the touch driver

Source: Apple Support; Google Pixel Help; Microsoft Support (Surface).

Apple's advice for a screen that responds intermittently runs in a sensible order: restart, clean the screen, unplug Lightning or USB-C accessories and try another cable or charger, then take off any case or screen protector. If part of the screen still does not respond, it suggests service. Google's Pixel help adds safe mode: if touch works there, a downloaded app is the likely cause. On the Pixel 8a and earlier, Screen protector mode, under Display and touch, then Touch sensitivity, raises sensitivity for use with a protector.

On Windows touch laptops, Microsoft's Surface guide suggests uninstalling the touch screen entries under Human Interface Devices in Device Manager, then scanning for hardware changes so Windows reinstalls them. Its hardware check is useful on any Surface: if touch does not work in the UEFI firmware screen, before Windows even starts, the hardware has likely failed.

Repair or replace?

A dead zone that survives a restart, a clean screen and no protector is almost always hardware. On most phones the touch layer is bonded to the display, so the repair is a screen replacement. Get a quote before paying for diagnostics, and check whether the device is still under warranty or covered by insurance.

Tests built into your device

A browser test is quick, but phones and some laptops carry their own diagnostics that can see more.

Built-in touch diagnostics
DeviceWhere to find itWhat it shows
iPhone, iPad Diagnostics mode in Recovery Assistant (hold the side button at startup) Display and touch tests
Android Developer options › Pointer location, or Show taps Crosshairs and coordinates for every touch
Google Pixel 9 Settings › Display and touch › touch diagnostics A guided touch test
Microsoft Surface UEFI screen (hold volume up, press power) Whether touch works before Windows loads

Source: Apple Support; Android Developers; Google Pixel Help; Microsoft Support.

Common questions

How many touch points should my phone support?

Most phones report 5 to the browser, per MDN, though the hardware may track more. For everyday use, two fingers for pinch and zoom is what matters; games and drawing apps use more.

Squares filled where I never touched. Why?

Those are ghost touches. Water on the glass, a faulty charger or nearby electronic equipment can all produce them; Microsoft's Surface guide suggests moving the device away from other electronics. If they appear with the screen dry and nothing plugged in, the screen needs service.

Can a screen protector cause dead zones?

It can weaken touch, especially at the edges or where there is an air bubble. Remove it and test again before blaming the screen.

Does the test work with a stylus or mouse?

Yes. A mouse counts only while the button is held, and a stylus behaves like one finger.

Is anything I draw saved?

No. What you draw and the squares you fill are held in this tab's memory only. The page does not upload or save them, and they are gone when you reset or leave the page. The site does count page views.

Sources

Last reviewed November 9, 2026.