What is a dead pixel test?
A dead pixel test fills your whole screen with one solid color at a time, so a pixel that is stuck or will not light shows up as a dot against a flat field. A single faulty pixel is about a quarter of a millimeter across on a typical laptop, and on a phone it is smaller still. Against a busy desktop it vanishes; against one flat color it stands out. To run it:
- Wipe the screen with a dry microfiber cloth. A speck of dust on the glass looks exactly like a dead pixel on white.
- Turn brightness up and switch off night light, True Tone or any blue-light filter, which tint the colors.
- Start the test and go through every screen. Scan in strips, top to bottom, rather than staring at the middle.
- Mark what you find. If a dot appears, note which screen showed it and roughly where. A photo with your phone helps if you later make a warranty claim.
On a new monitor or laptop, run the test on the first day, and check motion with our refresh rate test while you are at it. Return windows at many shops are short, and a pixel problem is easiest to argue while the product is still within them.
What is the difference between dead, stuck and hot pixels?
A dead pixel stays dark, a stuck pixel stays lit in one color, and a "hot" pixel stays fully lit as a white dot. Every pixel on an LCD or OLED screen is made of three subpixels, red, green and blue. Apple's support pages describe the mechanism plainly: each subpixel has its own transistor that switches it on and off, and if a transistor misbehaves, that subpixel stays off (dark) or stays on (bright). The names people use for the results are informal, and the table below sorts them out.
| Name | What happens | Easiest to see on | Can it change? |
|---|---|---|---|
| Dead pixel | All subpixels stay off | White | Rarely; usually permanent |
| Stuck subpixel | One subpixel stays on, a red, green or blue dot | Black | Sometimes comes and goes |
| Dark subpixel | One subpixel stays off | White or that subpixel’s color | Usually permanent |
| “Hot” pixel | Whole pixel stays on, a white dot | Black | Usually permanent |
Source: Apple Support, LCD display pixel anomalies; Dell Display Pixel Guidelines.
“Hot pixel” comes from camera sensors, where it means a sensor pixel that reads too bright. On screens it is loosely used for a pixel stuck fully on. Dell's guidelines add a fourth case that is easy to miss: a partial subpixel, a flaw less than half the size of a subpixel. Dell does not count these as defects, and you will not see one without a magnifier.
What each screen shows
The pure colors matter because they switch subpixels in a known pattern. On pure red, only red subpixels are lit. A dark dot there is a red subpixel that will not turn on; a green or blue dot is a subpixel of that color that will not turn off. Cyan, magenta and yellow each light two of the three, which catches the same faults from the other side.
| Screen | Subpixels lit | A fault shows as |
|---|---|---|
| 1. Black | None | Bright or colored dots (stuck pixels) |
| 2. White | All | Black dots (dead pixels), dust under the glass |
| 3. Red | Red | Dark or green and blue dots |
| 4. Green | Green | Dark or red and blue dots |
| 5. Blue | Blue | Dark or red and green dots |
| 6. Cyan | Green, blue | Dots that break the cyan |
| 7. Magenta | Red, blue | Dots that break the magenta |
| 8. Yellow | Red, green | Dots that break the yellow |
| 9. Gray | All at half level | Blotches, tint, darker corners |
| 10. Backlight bleed | None, with a gray frame | Light leaking in from the edges |
| 11. Gradient | All, rising left to right | Banding, uneven steps |
Source: The Daily Summit test screens; pure colors at full sRGB values.
Backlight bleed and uniformity
LCD screens make light with a backlight behind the panel and block it pixel by pixel. No panel blocks it perfectly, and where the frame presses on the edges, light can leak through as cloudy patches in the corners. That is backlight bleed. IPS panels also show a silvery “glow” that shifts as you move your head; bleed stays put. OLED screens have no backlight, since each pixel makes its own light, so they cannot bleed in this sense.
Use the bleed screen in a dim room at the brightness you normally use, sitting where you normally sit. Do not judge from a phone photo: cameras raise exposure in the dark and make mild bleed look dramatic. If the patches are visible in a dark scene of a film at your normal settings, it is worth raising with the seller.
The gray screen shows uniformity: darker corners, a warm or green tint in one area, or a faint vertical band. The gradient screen shows banding; if colors look wrong to you but the screen seems fine, our color blind test checks your color vision instead. The top half should change from black to white with no visible steps; the bottom half deliberately has 16, so you have something to compare against.
Does a warranty cover dead pixels?
Only if the number of faults passes the maker's pixel policy, and the limits differ by brand and model. Manufacturers do not promise a perfect panel by default. Most publish a pixel policy that sets how many faults are allowed before a screen counts as defective under warranty, and the numbers differ by brand, product line and sometimes model. Dell publishes one of the clearest. Under its Premium Panel Exchange, eligible monitors and laptops are replaced during the warranty if even one bright pixel appears, while dark subpixels are judged against a separate allowance.
| Product group | Bright pixels | Dark subpixels |
|---|---|---|
| Premium Panel Exchange monitors (UltraSharp and others) | 0 | up to 5* |
| Most standard Dell monitors | by model | up to 5 |
| Dell D-series monitors | by model | up to 8 |
| C-series and large-format (43 in and up) | by model | 12 to 15 |
Source: Dell Display Pixel Guidelines (article 000126004). *Some Alienware models allow up to 12. Check your exact model.
Apple takes a different approach in public: its support article says pixel anomalies occur in a small percentage of panels and asks owners to bring the product in for examination, without listing a count. Before you buy, search for “pixel policy” with the brand name, and keep the receipt. A shop's own return window, where it applies, is often more generous than the manufacturer's pixel policy.
Forum posts often quote “pixel classes” from industry standards. Whatever a standard says, a warranty claim is judged against the brand's own published policy for your model, so that is the document to read.
Can a pixel fixer repair a stuck pixel?
There is no reliable evidence that one can, and this page has none. Many sites offer a “stuck pixel fixer”, a small square that flashes colors very fast in the hope of jolting a subpixel back to life. We left it out for two reasons. The evidence that it works is anecdotal, and it is risky for some people: the Epilepsy Society says flashing at 3 to 30 times a second is the common trigger range for photosensitive seizures, which is exactly where these tools run. The web's accessibility guidelines (WCAG 2.3.1) ask pages not to flash more than three times in any second.
Dell's guidance is blunt too: do not attempt to fix stuck pixels yourself, and avoid pixel-fixing software or pressing on the screen, since that may void the warranty. If a stuck subpixel matters to you, the warranty is the fix.
Common questions
Is a dead pixel covered by warranty?
It depends on the maker's pixel policy and the number of faults. One dark subpixel is often within the allowance; one bright pixel on a Dell Premium Panel monitor is not. Check the policy for your model before you contact support.
Can a dead pixel spread?
A single faulty transistor does not damage its neighbors. A growing cluster of faults, lines or spreading blotches point to a different problem, such as pressure damage or a failing panel connection, which needs a repair shop.
Does this test work on a TV?
Yes, in the TV's browser or from a laptop. Open the page in the TV's browser, or on a laptop connected by HDMI with the browser window moved to the TV. Turn off picture modes that sharpen or boost contrast first, since they can hide faint faults.
Can my iPhone test itself?
Yes. Apple's Diagnostics mode, opened from Recovery Assistant at startup, includes a display test that shows colors and patterns and lets you mark any spots you find. This page works on an iPhone too, inside the browser. For the touch layer of a phone, use our touch screen test.
Is anything saved?
No. The colors are drawn by your browser, and the page does not record or upload which screens you looked at or what you saw. The site does count page views.
Sources
- Apple Support: About LCD display pixel anomalies for Apple products released in 2010 and later
- Apple Support: When and how to use diagnostics mode with iPhone and iPad
- Dell: Dell Display Pixel Guidelines
- W3C: Understanding WCAG 2.2, Three flashes or below threshold (2.3.1)
- Epilepsy Society: Photosensitive epilepsy
- MDN Web Docs: Fullscreen API
Last reviewed November 9, 2026.