Skip to content

Board foot calculator

Board feet and lumber cost from thickness, width and length.

Lumber type
%

Board feet to buy

18.4bf

Net, before waste
–
Cost to buy
–
Cubic feet
–
Cubic meters
–

Each board

    The board, and one board foot

    Billing practice differs by mill and dealer: check how your supplier measures before you order.

    How do you calculate board feet?

    A board foot calculator multiplies thickness in inches by width in inches by length in feet, then divides by 12. One board foot is the volume of a board 1 foot long, 1 foot wide and 1 inch thick: 144 cubic inches, or one twelfth of a cubic foot.

    Board feet
    bf = thickness (in) × width (in) × length (ft) ÷ 12

    Length in inches instead? Divide by 144 and leave out the 12. Price: board feet × price per board foot.

    How many board feet are in common boards?

    A 4/4 board 6 inches wide and 8 feet long holds 4 board feet; a 2 × 4 that is 8 feet long is billed as 5.33. The table lists common boards and the board feet in each linear foot.

    Board feet in common boards
    BoardBoard feetPer linear foot
    4/4 × 6 in × 8 ft 4.00 0.50
    4/4 × 8 in × 8 ft 5.33 0.67
    5/4 × 6 in × 8 ft 5.00 0.63
    8/4 × 6 in × 8 ft 8.00 1.00
    8/4 × 8 in × 10 ft 13.33 1.33
    2 × 4 × 8 ft (nominal) 5.33 0.67
    2 × 6 × 8 ft (nominal) 8.00 1.00
    1 × 12 × 10 ft (nominal) 10.00 1.00

    Source: calculated with bf = T × W × L ÷ 12 on nominal sizes.

    Worked example: a cut list for a bench
    1. Four 4/4 boards, 6 in wide, 8 ft long: 1 × 6 × 8 ÷ 12 = 4 bf each, 16 bf.
    2. Two 8/4 legs, 4 in wide, 4 ft long: 2 × 4 × 4 ÷ 12 = 2.67 bf each, 5.33 bf.
    3. Net total: 21.33 bf. With 15% waste: 21.33 × 1.15 = 24.5 bf.
    4. At 9.00 per board foot: about 220.80. The unit price calculator compares two yards quoting different units.

    Do you use nominal or actual size for board feet?

    Nominal. Lumber is billed on the rough thickness and width it was sawn at, not on what is left after drying and planing. That is why an 8-foot 2 × 4 is billed as 5.33 board feet while the stick you carry home holds 3.5. The surfaced size follows a fixed rule for dry softwood: take off ¼ inch under 2 inches nominal, ½ inch from 2 up to 8 inches, and ¾ inch from 8 inches up.

    Softwood: nominal and actual size, 8 ft long
    NominalActual (in)Billed bfReal bf
    1 × 4 3/4 × 3-1/2 2.67 1.75
    1 × 6 3/4 × 5-1/2 4.00 2.75
    2 × 4 1-1/2 × 3-1/2 5.33 3.50
    2 × 6 1-1/2 × 5-1/2 8.00 5.50
    2 × 8 1-1/2 × 7-1/4 10.67 7.25
    2 × 10 1-1/2 × 9-1/4 13.33 9.25
    2 × 12 1-1/2 × 11-1/4 16.00 11.25

    Source: dry dressed sizes by the American Softwood Lumber Standard (PS 20) reduction rule.

    1½ × 3½ 2 × 4 nominal, what you pay for Planed size is what you hold
    Cross-section of a 2 × 4, drawn to the same scale on both axes. Dashed line: nominal size.

    What do 4/4, 5/4 and 8/4 mean on hardwood?

    The numbers are quarters of an inch: 4/4 is 1 inch rough, 5/4 is 1¼ inches and 8/4 is 2 inches. Planed on both faces, a 4/4 board is typically 13/16 inch, which is why a hardwood dealer's 4/4 never measures a full inch.

    Hardwood quarters
    QuartersRough thicknessTypical surfaced (S2S)
    4/4 1 in 13/16 in
    5/4 1-1/4 in 1-1/16 in
    6/4 1-1/2 in 1-5/16 in
    8/4 2 in 1-3/4 in
    10/4 2-1/2 in not standard
    12/4 3 in not standard
    16/4 4 in not standard

    Source: Engineering ToolBox hardwood dimensions chart; there is no industry-wide standard for surfaced thickness, and 10/4 and up are normally sold rough.

    Hardwood is scaled a little differently from softwood, per WoodWeb: the board is measured by its actual width, the length is cut down to a whole foot, and board feet are rounded per piece. Softwood uses nominal dimensions. The calculator follows the plain formula, so a bundle bought by tally can differ from it by a few hundredths of a board foot per piece.

    How much lumber should you buy?

    Buy the net board feet plus a waste allowance for defects, saw kerf and trimming. There is no standard percentage; 10 to 20 percent is a common working allowance and the default here is 15, which is our own rule of thumb. Rough lumber for furniture with grain matching leans higher, straight framing lower. Round up to whole boards, since a short board cannot be stretched. The percentage calculator does the allowance by hand.

    How do board feet convert to cubic feet and meters?

    One board foot is one twelfth of a cubic foot, or 0.00236 cubic meters. A cubic meter of lumber is about 424 board feet.

    Board feet in cubic feet and cubic meters
    Board feetCubic feetCubic meters
    10 bf 0.83 0.024
    50 bf 4.17 0.118
    100 bf 8.33 0.236
    500 bf 41.67 1.180
    1000 bf 83.33 2.360

    Source: 1 bf = 144 in³ = 0.002359737 m³.

    What goes wrong with board foot math?

    • Measuring the planed board. A 13/16 inch board is still billed as 4/4, so use the quarters, not a tape measure.
    • Mixing units. Length in inches with the 12 divisor gives a number twelve times too big. Switch the length unit in the box instead.
    • Forgetting quantity. Price is per board foot of the whole order, not per board.
    • Skipping the waste. The cut list is the minimum, not the order. For areas rather than volume, the area calculator covers flooring and panels.

    Lengths come in feet and inches from many yards; the length converter handles centimeters and meters.

    Sources

    Last reviewed November 17, 2026. Board sizes and prices you type stay in this tab; nothing is uploaded. Waste allowance and the default price field are examples, not market data.