How do you run a speaker test?
Set your computer or phone to a low volume, then press Left. The sound should come only from the left speaker or the left earcup. Press Right, then Both, which should sit in the middle, between the speakers or inside your head on headphones. If all three sound right, your channels are fine.
Every sound is generated by your browser as you press the button, starting at −30 dB below full scale, so turn things up gradually. The page never asks for your microphone; to test input too, use our microphone test.
Tone is clearest for headphones. Noise is easiest to place in a room. Voice sits where speech does, for a laptop used on calls.
Left, right and both
A swapped result, left playing on the right, almost always means the headphones are on backward or the speaker cables are crossed at the back of the amplifier. Check the small L and R marks on the earcups or the speaker terminals. If Left and Right both play from both sides, the system is set to mono, or you are listening on a single speaker, as on most phones and many laptops. Where a laptop has two speakers a few inches apart, hold your head close to the middle to hear the difference.
Why does one side play no sound?
When one side is silent, first try a different pair of headphones. If the fault follows the headphones, they are damaged, often at the plug or where the cable meets the earcup. If it stays with the device, check its balance and mono settings.
| Device | Where to look |
|---|---|
| Windows 11 | Settings > Accessibility > Audio: the Mono audio switch |
| macOS | System Settings > Sound > Output: choose the device, then the Balance slider |
| iPhone | Settings > Accessibility > Audio & Visual: Mono Audio and the Balance slider |
| Android | Settings > Accessibility: look for audio adjustment, Mono audio and a balance slider (names vary by maker) |
Source: Microsoft Support, Apple Support, checked November 2026; Android menu names differ between manufacturers.
On Bluetooth, a headset in hands-free mode for a call can drop to mono until the call ends.
What does the frequency sweep show about your hearing?
It shows where your speakers, or your ears, stop reproducing high and low pitches; the test cannot tell which. The sweep glides from 20 Hz to 20,000 Hz (20 kHz), the range usually given for human hearing, though the top end is for young people. Listen for rattles along the way: a sharp buzz at one point usually means something loose in a speaker cabinet, a laptop chassis, or the desk underneath.
| Finding | Source |
|---|---|
| People can detect sounds from about 20 Hz to 20 kHz; average adults often top out around 15 to 17 kHz | Purves and others, Neuroscience, 2nd edition |
| Long or repeated exposure to sounds at or above 85 dBA can cause hearing loss | US National Institute on Deafness and Other Communication Disorders (NIDCD) |
Source: NCBI Bookshelf; NIDCD.
The 85 dBA figure is a level in the room or at your ear, which this page cannot measure: dB here are relative to the loudest signal your device can produce. To check that the same device records sound cleanly, capture a sample with the voice recorder.
Bass tones and the notes they match
The bass buttons play steady tones from 20 to 150 Hz. Most laptop and phone speakers produce very little below about 100 Hz, so the low buttons may seem silent on them; that is normal. On a subwoofer or good headphones, the lowest one you can hear clearly is your system's practical bass limit. A flapping or buzzing sound means the speaker is being pushed too hard: turn the level down.
| Note | Frequency (Hz) | Where you hear it |
|---|---|---|
| A0 | 27.5 | Lowest key on a standard 88-key piano |
| B0 | 30.9 | Lowest string on a five-string bass guitar |
| E1 | 41.2 | Lowest string on a standard four-string bass |
| A1 | 55.0 | Open A string on a bass guitar |
| E2 | 82.4 | Lowest string on a standard guitar |
| C4 | 261.6 | Middle C |
Source: calculated in equal temperament with A4 = 440 Hz.
What is the phase check?
It tells you whether both speakers push and pull air in step. Wired the same way, they sound solid and centered. If one has its positive and negative wires swapped, they work against each other: the image smears to the sides and bass thins out.
The Out of phase button flips the right channel on purpose so you can hear the difference. If In phase is the one that sounds hollow, swap the red and black wires on one speaker, at the speaker or the amplifier, and test again. On a single speaker, out-of-phase sound can almost vanish, since the two channels cancel when they are added together.
Common questions
Is this a hearing test?
No. The levels are not calibrated, and the result depends as much on your speakers as on your ears. Setting up a call? Our webcam test covers the camera side. For information only; not medical advice.
Can the test damage my speakers?
At sensible levels, no. Stop and turn down if you hear distortion.
Why can't I choose an output device?
Only some browsers let a web page pick where sound plays. When yours does, a "Play through" list or a "Choose output device" button appears; otherwise the page uses whatever your system's sound settings have selected.
Sources
- Purves and others, Neuroscience, 2nd edition: The Audible Spectrum (NCBI Bookshelf)
- The Physics Factbook: Frequency range of human hearing
- NIDCD: Noise-induced hearing loss
- NIDCD: Age-related hearing loss
- World Health Organization: Deafness and hearing loss
- Microsoft Support: Make Windows easier to hear
- Apple Support: Change Sound Output settings on Mac
- Apple Support: Audio and visual accessibility settings on iPhone
- MDN Web Docs: StereoPannerNode
- MDN Web Docs: HTMLMediaElement setSinkId()
Last reviewed November 9, 2026. For information only; not medical advice.