Skip to content

Tire size calculator

Compare two tire sizes: diameter, sidewall and speedometer error.

Speed unit

Outside diameter change

+1.7%

Within the common 3% guideline.

MeasureCurrentNewChange
The two tires to scale

Side view on the left, seen from the front on the right, both resting on the same ground line.

Current New

What the speedometer shows

With the new tires and a dash set for the old ones.

Dash showsTrue speedDifference

Calculated sizes are nominal; real tires vary by brand and wear. Check fitment with a tire shop or your owner's manual.

How do you read a tire size?

A size such as 225/45R17 has three numbers: the width in millimeters (225), the aspect ratio (45) and the rim diameter in inches (17). The aspect ratio is the sidewall height as a percentage of the width, so the sidewall is 225 × 0.45 = 101.25 mm. Outside diameter is two sidewalls plus the rim: 2 × 101.25 + 17 × 25.4 = 634.3 mm, which is 24.97 inches.

225/45R17, number by number
PartPrintedMetricHow
Width 225 225 mm tread to tread, as printed
Aspect ratio 45 101.25 mm 45% of the width = sidewall height
Rim 17 431.8 mm 17 in × 25.4
Outside diameter 634.3 mm 2 × 101.25 + 431.8 = 24.97 in

Source: the standard tire code, as set out in the Wikipedia article Tire code; the arithmetic is ours.

How do you compare two tire sizes?

Work out the outside diameter of each, then take the percentage difference. A tire calculator does this and also gives the circumference, the number of times the tire turns in a mile or kilometer and how far the sidewall changes. Circumference is π times the diameter; the scientific calculator has π and the percentage calculator the difference step.

Worked example: 225/45R17 to 235/40R18
  1. Current: 2 × 101.25 + 431.8 = 634.3 mm.
  2. New: sidewall 235 × 0.40 = 94 mm, so 2 × 94 + 457.2 = 645.2 mm.
  3. Difference: (645.2 − 634.3) ÷ 634.3 = +1.72%, or 10.9 mm taller, so the axle rides 5.5 mm higher.
  4. The tire is 10 mm wider and the sidewall 7.25 mm shorter. Revolutions per mile fall from 808 to 794.

Revolutions per mile is the number to use for gearing and speed. A wheel that makes 808 turns a mile turns 808 times a minute at 60 mph, and 794 times at the same road speed on the larger tire, which is why the dash, set to count turns, reads 1.7 percent low. Revolutions per kilometer work the same way: 502 for the 225/45R17 and 493 for the 235/40R18. Both figures assume the tire holds its printed size; a loaded or worn tire has a slightly smaller rolling radius, so use them as a guide.

What is the 3% rule for tire sizes?

It is a rule of thumb, repeated by tire retailers, that a replacement should stay within about 3 percent of the original outside diameter. It is not a law or a manufacturer specification, and clearance, load rating and rim width matter too. The calculator shows where your swap lands against it and nothing more.

Common swaps
SwapDiameter (in)Change3% guideline
225/45R17 to 235/40R18 24.97 to 25.40 +1.7% within
205/55R16 to 225/45R17 24.88 to 24.97 +0.4% within
195/65R15 to 205/60R16 24.98 to 25.69 +2.8% within
215/60R16 to 225/55R17 26.16 to 26.74 +2.2% within
265/70R17 to 285/70R17 31.61 to 32.71 +3.5% outside
265/65R18 to 275/60R20 31.56 to 32.99 +4.5% outside

Source: calculated here from the tire code; nominal sizes.

What does the speedometer read after the change?

The dash counts wheel turns, so a bigger tire covers more road per turn and the dash reads low. With a dash set for the old size, true speed is the displayed speed times the new diameter over the old. At +1.72 percent a dash reading of 100 means 101.7. The odometer under-counts by the same share.

True speed for a dash reading (any unit)
Dash showsDiameter +1.7%+3%+5%
50 50.8 51.5 52.5
80 81.4 82.4 84.0
100 101.7 103.0 105.0
120 122.0 123.6 126.0

Source: calculated here; true speed = dash speed × new diameter ÷ old diameter.

The legal side is about the dash reading high, not low. UN Regulation 39, which covers speedometers in the countries that apply UN vehicle rules, says the displayed speed may not be less than the true speed and may be at most 10 percent of the true speed plus 4 km/h above it, tested at set speeds. A taller tire pushes a dash toward reading low, which is the case the rule does not allow.

What stays the same in plus sizing?

Plus sizing puts a bigger rim with a lower-profile, usually wider tire so the outside diameter barely moves. The rim grows by 1 inch, the sidewall shrinks, and the outside height stays within a couple of percent.

Shaded ring is the sidewall. Same scale for all three; diameters 631.9, 634.3 and 645.2 mm.

What do people get wrong when changing tire size?

  • Comparing only the width. A wider tire with a lower profile can be the same height; a narrower one with a taller profile can be much taller.
  • Reading the 3% as a pass mark. It limits the speedometer error; it does not check fit, load index or speed rating.
  • Forgetting wear. A new tire is taller than a worn one of the same size, so the dash reads differently on the day you fit it.
  • Trusting the printed size alone. Brands differ by a few millimeters at the same size, so this tool gives nominal figures.
  • Ignoring the odometer. A 2 percent error is 20 km extra on a 1,000 km trip, which matters for fuel and service intervals. To change units, see the length converter.

Sources

Last reviewed November 17, 2026. The 3 percent figure is a widely quoted guideline from tire retailers, not a standard. It runs in your browser; nothing you enter is sent anywhere.